The process of replacing a kitchen sink is simple yet time-consuming. Sinks come in a variety of styles, dimensions, and materials, some of which are more challenging to deal with than others. We’ll explain how to replace a kitchen sink in this post.
We’ve covered how to replace pipes, cut the counter for a new sink, remove an old sink, and install a kitchen sink for the first time.
What Is the Time Frame for Kitchen Sink Replacement?
An experienced installer would typically need between 1.5 and 2 hours to install a basic sink with dimensions of 80 cm x 55 cm x 20 cm. However, there are a number of variables that affect the task at hand. How simple it is to remove the old sink, for instance. how much repair work is required for the hole and whether new pipes are required.
Taking Out a Kitchen Sink
To replace a kitchen sink, you must first remove the old one.
You must approach this task carefully to avoid damaging the new sink or the countertop.
We urge you to contact experienced plumbers and get the sink changed if you’re not completely confident in your DIY plumbing abilities.
To make it simpler to install the new unit, snap a photo of the pipes under the sink before you disconnect them.
Equipment and Other Tools You May Need
Pliers with adjustable wrench
Screwdriver
Knife like a Stanley
An old towel and a bucket
Step 1. Disconnect the supply lines and turn off the water supply.
Stop both the supply of hot and cold water to the sink before removing it. The supply lines and drain pipe that connect to the home drainage system should then be disconnected using the adjustable wrench.
Step 2: Empty the bucket under your sink and drain the remaining water.
The pipes should be thoroughly drained because it’s conceivable that some water will remain within. Put a bucket underneath the sink and turn on the water. Remove the bucket and shut off the faucet when nothing is left.
Step 3: Disconnect the dishwasher and your waste disposal.
Disconnect your dishwasher and any under-sink garbage disposals you may have as well. Disconnect your water filter system from the faucet if you have one. You might wish to first verify the instructions for any equipment before attempting to do so.
Keep a pail and a rag close hand while disconnecting any device because there can be leaks.
Step 4: Disconnect the p-trap and drain pipes.
If you haven’t already, now is the time to start. Take the drain pipe and p-trap pipes out from under the sink. Before changing the sink, please sure to remove any additional sink components.
Step 5: Cut the caulk and unscrew the metal clips.
After that, you must remove the metal clips. For both top and under-mount sinks, they are situated beneath the sink. You must cut the caulk after removing the clips. The placement of the caulk distinguishes the two types of sinks. For top-mounted sinks, it is on top where the larger section of the sink meets the counter, whereas for under-mount sinks, it is underneath the sink where the metal clips are.
Step 6: Dispose away the outdated sink and remove any caulk.
Remove the sink once you have finished cutting the caulk. After that, wipe the counter and scrape off any residual caulking.
Installing a Kitchen Sink
If you are well prepared and experienced with DIY home projects, installing a sink is simple. Additionally, you may always get a nearby plumber to assist you if the task appears too difficult.
Fortunately, this section of our comprehensive tutorial includes step-by-step instructions on how to install a kitchen sink. But first, determine what supplies and tools you’ll need.
Equipment and Other Tools You May Need
Power pencil saw
Jigsaw Drill (plus 10 or 15 mm drill bits)
Sandpaper or pliers
an impermeable sealant
Toilet paper tape
Screwdriver
a flexible wrench
Step 1 is to install your new sink and secure it.
The top-mounting sink should be turned over, and the wider part should be caulked. Next, carefully flip the sink over and set it into the opening. Remove any extra caulking if there is any.
The caulk goes in a different spot when installing an under-mount sink, but the process is otherwise the same. You apply the caulk on top of the sink while using this kind of sink. Place the sink underneath the countertop after spreading it out evenly all over the top. To support the sink while the glue sets, use something as a base.
No of the model, we advise using water-resistant silicone caulk when installing a sink.
Step 2: Fit your faucet and attach the metal sink clips.
Reattach the metal sink clamps from the prior sink once the caulk has dried. Once more, put them underneath the sink and tighten them up tightly to secure it. After the sink is installed, you can move on to installing the tap.
Step 3 is to secure and seal the drain strainer.
You can use plumber’s putty to install your new drain strainer. Spread a tiny portion of it evenly around the rim after rolling a small piece of it between your fingers to make it more flexible. Place the strainer there and secure the drain. Use a cutting tool to scrape off any extra putty if there is any.
Reconnect your water supply lines in step four.
Reattach the supply pipes for hot and cold water to the new tap. Connect the faucet to the other end of each metal connector by placing them over the lines. To that, use a wrench to tighten the fastening, being cautious not to overtighten it.
Step 5: Install your dishwasher and waste disposal.
This step should be simple if you followed our advise and took a snapshot of each pipe before demounting it. If not, you can reinstall them using the instructions for the dishwasher and garbage disposal.
The garbage disposal should be quite easy to install. The majority of units are fastened to the drain and put over its bottom.The little spout on the pipes or the waste disposal unit is where you should attach the dishwasher hose. Then use a hose clamp to secure it.
Step 6: Join the pipes together and look for leaks.
If you have a garbage disposal, the sink’s drainpipe ought to be placed on the side of the appliance. If such a unit is absent, the drainpipe connects the drain with the main drain line. P-trap pipes make it simple to connect the drain pipes. Each pipe should be fastened, but not too tightly.
Turn on the water supply after finishing this final installation stage to check your work. If there are any leaks, don’t forget to put a bucket under the sink and pipes.
Countertop preparation for the new kitchen sink involves cutting
Step 1: Mark the dimensions of your sink
Take measurements of the sink’s bottom first. With a graphite pencil and a ruler, make the appropriate measurement. Remember that the narrower top side of the sink should not be used for measurements. The broader portion is used to glue down the sink and rests on top of the kitchen counter.
Step 2: Drill the countertop’s corner holes and trim it.
Drill four holes at the marking’s four corners next. Drill the apertures on the opposing sides of a circular sink. Starting from one of the holes you’ve made, use the jigsaw to cut the countertop, making sure it has excellent support. To prevent the countertop from breaking when you’re trying to make an even cut, you need a sturdy base. Contact a professional if you require any help with your kitchen installation projects.
Step 3: Level the surface.
To make the sliced surface smoother, use pliers or sandpaper. Avoid getting too involved or you might bend the cut. When you’re through, wipe the dust away to create a tidy workspace.
Kitchen sink drain pipe replacement
It will be simple to replace the drain pipes under the sink if you followed our recommendation to snap a photo of the pipes before demounting them.
The following are the most frequent justifications for replacing both the sink and the pipe:
For the new unit, the current drain line is too small.
also, it is too long for the new sink.
if the pipe is rusty and worn out
Lastly, if the pipe needs to be replaced because it is broken,
A Kitchen Sink Drain Pipe Connection
To determine how long it has to be, measure the distance from the sink’s drain to the new one.
Purchase new pipe or precisely cut existing pipe.
Overlap a washer over the pipe’s end.
Place slip nuts at both ends of the pipe or on which it’s necessary.
After positioning the drainpipe, tighten the slip nut(s).
What is the Price of Installing a Kitchen Sink?
In addition to the sink’s price, a few other factors can affect how much the installation service will cost. For example, our kitchen sink installation service in London, on average, costs roughly £98 per hour. When an old sink needs to be removed first, installing a new sink can frequently take up to two hours. The cost could also change depending on the day or day of the week the job is done. It’s always preferable to get a project quote that is accurate. When you join the Fantastic Club, you can benefit from savings and a host of other advantages.
Main Points
In conclusion, if you’re wanting to do another DIY project, maybe this comprehensive guide can assist you in installing a kitchen sink. The task should go easily if the steps for each step in the procedure are followed. The following are the most crucial considerations when changing a sink:
Take care when using the old and new sinks and the countertop.
Before caulking and installing the new unit, prepare and clean the work area.
Before disconnecting the pipes under the sink, take a picture of them.
When you are finished, check the pipes for leaks.
Kitchen Sink Replacement: From Removal to Fitting and Cutting
Need support? Call us to hire the dreamhomedesign professionals right now.
